Log Board Foot Calculator
Measure the diameter at the small end of the log, inside the bark. Pick a log rule and enter the length. Log rules give estimates, not guaranteed lumber yield.
Quick Answer
To estimate board feet in a log, measure the diameter at the small end inside the bark and the length. Then apply a log rule: Doyle, Scribner or International 1/4″. The same log gives a different answer under each rule, so ask your buyer or sawyer which one they use.
Key Takeaways
- Measure the small end of the log, inside the bark.
- Doyle usually gives the lowest estimate, especially on small logs.
- International 1/4″ is generally the closest to real lumber yield.
- Log rules estimate lumber. They do not guarantee it.
- Always agree on the rule before you buy or sell logs.
What Is a Log Rule?
A log rule is a formula or table that estimates how many board feet of lumber a log can make. It allows for sawdust, slabs and waste, so it isn’t the same as the log’s total volume. A board foot is 1 inch × 12 inches × 12 inches.
The Three Common Rules
Doyle
BF = (D − 4)² × L ÷ 16
Common in the southern US and often used by log buyers. It tends to underestimate small logs.
Scribner
BF = (0.79 × D² − 2 × D − 4) × L ÷ 16
This is a common approximation of the Scribner rule, which is traditionally a table. It is used widely in the western US.
International 1/4-inch
BF = 0.905 × (0.22 × D² − 0.71 × D) for every 4 feet of length. The rule adds a half-inch of diameter for each 4-foot section, to allow for taper.
It allows for a 1/4-inch saw kerf and is often used as a benchmark for other rules.
Here, D is the small-end diameter in inches and L is the length in feet.
Understanding Log Scales and Log Rules
Same Log, Different Answers
Estimates for a 16-foot log:
| Small-end diameter | Doyle | Scribner | International 1/4″ |
|---|---|---|---|
| 10 in | 36 | 55 | 65 |
| 12 in | 64 | 86 | 97 |
| 16 in | 144 | 166 | 181 |
| 20 in | 256 | 272 | 290 |
On small logs the gap is large. On bigger logs the three rules move closer together.
Worked Example
A log is 14 inches across at the small end, inside the bark, and 12 feet long.
- Doyle: (14 − 4)² × 12 ÷ 16 = 75 bf
- Scribner: about 92 bf
- International 1/4″: about 98 bf
How to Measure a Log
- Find the small end of the log.
- Measure straight across the end, inside the bark. Average two measurements if the log isn’t round.
- Measure the length in feet.
- Check whether your buyer rounds the length or adds trim allowance.
Why Your Lumber May Not Match the Number
Log rules are estimates. Real yield depends on:
- the sawmill and blade thickness (kerf)
- log taper, crook and defects
- how the sawyer cuts the log
- the grade of lumber you want
Sawyers sometimes get more lumber than the rule says. That is called overrun.
Also check:
Deck Stairs: Guide to Layout, Cutting, and Installation
Deck Material & Board Calculator (Free Online Tool)
Deck Stain Calculator: Estimate How Much Stain You Need
Board Foot Calculator: Find Out How Much Lumber You Need
Linear Feet to Square Feet Calculator: Board Width Converter
Board Feet to Square Feet Calculator: Convert Lumber Easily
Common Mistakes
- Measuring the big end or measuring over the bark.
- Not knowing which rule a buyer uses.
- Treating the estimate as guaranteed lumber.
- Mixing up inches and feet.
FAQ
Which log rule is most accurate?
International 1/4″ is generally the closest to real lumber yield. Doyle usually underestimates small logs.
How do I calculate board feet in a log?
Measure the small-end diameter inside the bark and the length, then use a log rule such as Doyle, Scribner or International 1/4″.
Why does Doyle give lower numbers?
It takes off a fixed 4 inches from the diameter before squaring, which cuts small logs the most.
Where do I measure log diameter?
At the small end, inside the bark.
Can I use this for standing trees?
No. This tool is for cut logs. Standing trees need different formulas that allow for height and taper.
Is the Scribner result exact?
No. It uses a common formula approximation of the Scribner table.
Before You Buy or Sell
Agree on the log rule, the measuring method and the price before any sale. Follow local rules for timber sales and manufacturer instructions for your sawmill.